LUFS Meter Online
How loud is your track, really? Drop in a file and read its loudness in LUFS, its sample peak in dBFS, and how many dB it sits above or below −14, −16 and −23 LUFS. Free, and your file never leaves your browser.
How to Measure LUFS Online
No account and no upload. One file, a few seconds.
Drop Your Audio
MP3, WAV, M4A, FLAC, OGG or AAC up to 200 MB. The file is decoded in your browser.
Read the Two Numbers
Integrated loudness shows how loud the whole file is in LUFS. Sample peak shows its loudest single sample in dBFS.
Compare With the Targets
Each target card says how many dB to turn the file up or down to reach it, and warns you when turning up would push the peaks past 0 dBFS.
What the LUFS Meter Tells You
The numbers you need before you deliver a file.
Loudness in LUFS
One number for how loud the whole file sounds, measured with K-weighting so bass and treble count the way your ears weigh them.
Sample Peak in dBFS
The loudest single sample across all channels, so you know how much room is left before 0 dBFS.
Gain to Three Targets
See how far the file is from −14, −16 and −23 LUFS, the levels most often asked for in streaming, podcasts and broadcast.
A Clipping Warning
When reaching a target means turning up so far that the peaks would pass 0 dBFS, the card tells you the file needs limiting first.
A Waveform at True Scale
The waveform is drawn against full scale, not stretched to fit, so a quiet file looks quiet and a loud one looks full.
Measured on Your Device
Decoding and measuring run in your browser. Unreleased mixes and episodes never leave your computer or phone.
Your File Stays on Your Device
The file is decoded and measured in your own browser. It is never uploaded, so there is nothing on a server to delete afterwards.
No Upload
Measured on your own device
No Account
Drop a file and read the result
Read Only
Your file is never changed
Who Checks LUFS
Anyone who needs a file to land at the right loudness.
Podcasters
Check an episode against −16 LUFS before you publish it
Musicians and Mixers
See how loud a master is next to the −14 LUFS level common for streaming
Broadcast Delivery
Check a file against −23 LUFS before you hand it over
Video Creators
Make sure a voiceover or soundtrack isn’t far quieter or louder than the rest
Audiobook Narrators
Compare chapters so each one comes out at a similar loudness
Album and Playlist Checks
Measure each track to find the one that sticks out
Know How Loud Your Audio Is Before You Send It
Peak level tells you how close a file gets to the top. It doesn’t tell you how loud it feels. Two files can peak at the same level and still sound very different in volume, which is why delivery specs ask for loudness in LUFS instead. Drop a file here and you get both numbers, plus how far you are from the targets people ask for most.
What this meter measures
The loudness number is K-weighted: the audio is filtered with a high-shelf and a high-pass filter that approximate the weighting in the loudness standard, so very low bass counts for less and the upper mids count for a bit more, closer to how we hear. The weighted signal is then averaged over the whole file, from the first sample to the last. Sample peak is the largest single sample on any channel, in dBFS.
What it doesn’t measure
This is a quick check, not a certified loudness meter. It does not apply the gating that the full standard uses to ignore silence, so long pauses or a quiet intro pull the number down, and its result can differ from a meter that follows the standard exactly. It reports sample peak, not true peak, and it does not measure loudness range or short-term loudness. For a final delivery that has to pass a strict check, confirm with a meter built for that.
Fixing what you find
If the file is too quiet or too loud, the loudness normalizer moves it to −14, −16 or −23 LUFS in one step. If you only want to raise a file until its peak reaches a safe level, the peak normalizer does that. When turning up would clip, tame the peaks first with the audio limiter, or even out the dynamics with the audio compressor.
Comparing files and looking closer
Checking two versions of a mix? The audio compare tool plays them in sync and can match their loudness, so you hear the difference in sound rather than in volume. To see where the energy in a file sits, from bass to treble, open it in the spectrum analyzer.
Need to Change the Loudness Too?
The full Notevibes Online Audio Editor has a loudness normalizer, limiter, compressor, EQ and effects, and exports to MP3 or WAV, all in your browser.
Free to try · No credit card required
Related Audio Tools
More free AI audio tools from Notevibes — same engine, no sign-up.
Loudness Normalizer
Match perceived loudness to broadcast LUFS targets.
Audio Normalizer
Boost audio to peak volume without clipping.
Audio Limiter
Brick-wall limit peaks without distortion.
Audio Compressor
Even out loud and quiet parts with dynamics compression.
Spectrum Analyzer
See the frequencies in a file or your mic, live.
Audio Compare
Switch between two audio files to hear the difference.
LUFS Meter FAQ
What is LUFS?
LUFS stands for Loudness Units relative to Full Scale. It measures how loud audio sounds to people, not just how high its peaks go. One LU is the same size step as one dB.
How do I check the LUFS of a song or podcast?
Drop the file onto the meter. A moment later you see its loudness in LUFS, its sample peak in dBFS, and how many dB it is from −14, −16 and −23 LUFS.
What LUFS should my audio be?
It depends on where it is going. −14 LUFS is common for music streaming, −16 LUFS for podcasts and spoken word, and −23 LUFS for broadcast. Always check the exact figure your destination asks for.
Is this integrated loudness?
It is the loudness of the whole file as one number, K-weighted and averaged from start to finish. It does not use the gating of the full standard, so long silences lower the result, and it may read differently from a meter that applies that gating.
Does it measure true peak?
No. It shows the sample peak, the largest single sample in the file. True peak also estimates the peaks that can appear between samples and is usually a little higher.
How do I change the loudness after measuring?
Use the loudness normalizer. Pick −14, −16 or −23 LUFS and it applies the gain for you. If the target would push the peaks past 0 dBFS, run a limiter first.
Is my file uploaded?
No. The file is decoded and measured in your browser and never leaves your device. The meter only reads it and never changes it.
Which formats can I measure?
MP3, WAV, M4A, FLAC, OGG and AAC up to 200 MB, and anything else your browser can decode.